["Assessment, Performed": "Standardized Tools Score for Assessment of Cognition"]
Data Element Scope: This value set may use a model element related to Assessment.
Inclusion Criteria: Includes concepts that describe assessments with total score results for the following standardized tools: -Blessed Orientation-Memory-Concentration Test (BOMC) -Montreal Cognitive Assessment (MoCA) -St. Louis University Mental Status Examination (SLUMS) -Mini-Mental State Examination (MMSE) [Note: The MMSE has not been well validated for non-Alzheimer's dementias] -Short Informant Questionnaire on Cognitive Decline in the Elderly (IQCODE) -Ascertain Dementia 8 (AD8) Questionnaire -Minimum Data Set (MDS) Brief Interview of Mental Status (BIMS) [Note: Validated for use with nursing home patients only] -Formal neuropsychological evaluation -Mini-Cog.
Exclusion Criteria: No exclusions.
Constrained to codes in the Standardized Tools Score for Assessment of Cognition value set (2.16.840.1.113883.3.526.3.1006)
"Assessment, Performed"
Data elements that meet criteria using this datatype should document completion of the assessment indicated by the QDM category and its corresponding value set.
Timing:
- relevant dateTime references timing for an assessment that occurs at a single point in time.
- relevant Period references a start and stop time for an assessment that occurs over a time interval
- author dateTime references the time the action was recorded.
- Refer to the eCQM expression to determine allowable timings to meet measure criterion.
Note: negation rationale indicates a one-time documentation of a reason an activity is not performed. Negation of QDM datatype-related actions for a reason always use the author dateTime attribute to reference timing and must not use relevantPeriod.
authorDateTime
The time the data element was entered into the clinical software. Note, some datatypes include both relevant dateTime and author dateTime attributes. When both are present, author dateTime is included to accommodate negation rationale.
The author dateTime addresses when an activity is documented. Documentation can occur at the beginning, during, at the end, or subsequent to the end of the activity. The author dateTime should be used only if the relevantPeriod cannot be obtained or to represent the time negation rationale is documented.
Note: negation rationale indicates a one-time documentation of a reason an activity is not performed. Negation of QDM datatype related actions for a reason always use the author dateTime attribute to reference timing and must not use relevantPeriod.
negationRationale
Indicates the reason that an action was not performed. Only QDM datatypes that represent actions (e.g., performed, recommended, communication, order, dispensed) allow the negation rationale attribute. The intent is to indicate a justification that such action did not happen as expected. This attribute specifically does not address the presence or absence of information in a clinical record (e.g., documented absence of allergies versus lack of documentation about allergies). QDM assumes a world view that absence of evidence indicates information does not exist or an action did not happen. To express such lack of evidence, an eCQM author should use the CQL expression not exists with reference to the data element rather than the QDM data model. negation rationale in QDM signifies only a reason for such absence, i.e., the reason must be present to qualify for negation rationale. The syntax in the human readable HQMF is addressed in CQL examples and in the MAT User Guide. Prior versions of QDM used the syntax, Procedure, Performed not done. QDM versions starting with 5.3 use the syntax, Procedure, not Performed. Section A-5 provides examples for expressing negation rationale in CQL.
Note: negation rationale indicates a one-time documentation of a reason an activity is not performed. Negation of QDM datatype-related actions for a reason always use the author dateTime attribute to reference timing and must not use relevantPeriod.
For updated guidance and implementer feedback regarding use of the QDM negation rationale attribute see Section 6.6.
relevantDateTime
relevantPeriod
relevantPeriod addresses the time between the start of an action to the end of an action. Each QDM datatype using relevantPeriod defines specific definitions for the start and stop time for the action listed.
Note: negation rationale indicates a one-time documentation of a reason an activity is not performed. Negation of QDM datatype-related actions for a reason always use the author dateTime attribute to reference timing and must not use relevantPeriod
result
The final consequences or data collected from the datatype. results can be used in four ways to express:
- That a result is present in the electronic record but any entry is acceptable
- A numerical result is reported directly as a value. Values may be integers or decimal numbers without units, or as a quantity with a value and units - examples:
- 100mg/dL for a lab test
- 140 mmHg for blood pressure
- as a percentage (actually as a quantity with % as units)
- as a titer or ratio (e.g., 1:4, 1:80)
- A result that matches one of a specific set of coded concepts in a value set or a code that matches a direct reference code
- A result as a dateTime ("Assessment, Performed" and components)