"Medication, Administered"
Data elements that meet criteria using this datatype should document that the medication indicated by the QDM category and its corresponding value set was actually administered to the patient.
Timing:
- relevant dateTime references the time the medication is administered if it was given or taken at a single point in time.
- relevantPeriod references a start and stop time for medication administration if the administration event occurred over a time interval (e.g., an intravenous infusion). The relevantPeriod addresses:
- startTime - when a single medication administration event starts (e.g., the initiation of an intravenous infusion).
- stopTime - when a single medication administration event ends (e.g., the end time of the intravenous infusion).
- author dateTime references the time the action was recorded.
- Refer to the eCQM expression to determine allowable timings to meet measure criterion.
Notes:
- Measure developers should address multiple administrations over a period of time using CQL logic.
- negation rationale indicates a one-time documentation of a reason an activity is not performed. Negation of QDM datatype-related actions for a reason always use the author dateTime attribute to reference timing and must not use relevantPeriod.
Refer to Special Cases in Section 5.7 for scenarios to consider in calculating cumulative medication duration.
Medication
authorDateTime
The time the data element was entered into the clinical software. Note, some datatypes include both relevant dateTime and author dateTime attributes. When both are present, author dateTime is included to accommodate negation rationale.
The author dateTime addresses when an activity is documented. Documentation can occur at the beginning, during, at the end, or subsequent to the end of the activity. The author dateTime should be used only if the relevantPeriod cannot be obtained or to represent the time negation rationale is documented.
Note: negation rationale indicates a one-time documentation of a reason an activity is not performed. Negation of QDM datatype related actions for a reason always use the author dateTime attribute to reference timing and must not use relevantPeriod.
dosage
frequency
- Is administered to a patient for an active medication (a).
- Was administered to the patient (b).
- Should be taken by the patient or administered to the patient (c).
- Is recommended to be given to the patient (d).
negationRationale
Indicates the reason that an action was not performed. Only QDM datatypes that represent actions (e.g., performed, recommended, communication, order, dispensed) allow the negation rationale attribute. The intent is to indicate a justification that such action did not happen as expected. This attribute specifically does not address the presence or absence of information in a clinical record (e.g., documented absence of allergies versus lack of documentation about allergies). QDM assumes a world view that absence of evidence indicates information does not exist or an action did not happen. To express such lack of evidence, an eCQM author should use the CQL expression not exists with reference to the data element rather than the QDM data model. negation rationale in QDM signifies only a reason for such absence, i.e., the reason must be present to qualify for negation rationale. The syntax in the human readable HQMF is addressed in CQL examples and in the MAT User Guide. Prior versions of QDM used the syntax, Procedure, Performed not done. QDM versions starting with 5.3 use the syntax, Procedure, not Performed. Section A-5 provides examples for expressing negation rationale in CQL.
Note: negation rationale indicates a one-time documentation of a reason an activity is not performed. Negation of QDM datatype-related actions for a reason always use the author dateTime attribute to reference timing and must not use relevantPeriod.
For updated guidance and implementer feedback regarding use of the QDM negation rationale attribute see Section 6.6.
performer
The performer is the person or organization that is responsible for the action (e.g., the individual or organization carrying out the activity). The performer references a QDM entity and any or all of the attributes of the selected QDM entity. For example, to reference that a physician who performed a procedure is the same person who was the primary participant in an Encounter and assure the physician’s specialty meets the measure’s requirements, the eCQM can reference the Practitioner entity and its attributes. Should the eCQM choose to reference a physician practice or a hospital, the performer can reference the Organization entity and indicate the identifier and/or the organization type.
[See Sections 2.6 and 4.2 for description of Entities]
reason
The thought process or justification for the datatype. In some measures, specific treatments are acceptable inclusion criteria only if a justified reason is present. Each of these measures uses a value set (often, but not exclusively, using SNOMED CT) to express acceptable justification reasons. Other measures specify reasons as justification for exclusions.
Examples include patient, system, or medical-related reasons for declining to perform specific actions. Each of these measures also uses a value set to express acceptable justification reasons for declining to perform expected actions.
relevantDateTime
relevantPeriod
relevantPeriod addresses the time between the start of an action to the end of an action. Each QDM datatype using relevantPeriod defines specific definitions for the start and stop time for the action listed.
Note: negation rationale indicates a one-time documentation of a reason an activity is not performed. Negation of QDM datatype-related actions for a reason always use the author dateTime attribute to reference timing and must not use relevantPeriod